I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
Hello,
I am testing the RF range of a BLE application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) with SDK 2.9.0.
In order to test the robustness...
Hi, I am having trouble setting up the partition manager in external flash with nRF54L15dk in NCS 3.0.0. I did not find any examples of this working. Interesting thing is...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Dear Nordic Support Team,
We have a system where an MCU is connected to a Wi-Fi module operating in NCP (Network Co-Processor) mode . The MCU controls the Wi-Fi chip to...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hi,
I'm using the nRF52832. And I was wondering if it really does support LLPM. I found sources that clearly state tat it does (e.g. the wireless mouse/keyboard example...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
