Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
We designed our own board using nRF8001 and EMF32, I used the EMF32 development kit to test the code and it is working fine. When I down the same code to my own board, it...
Hi ,
I am planning to implement S120 UART to communicate with desktop as well as S110 UART BLE.
I browsed in the forum and found out we already have example in github...
I have a small nRF51822 module that I want to use for UART communication without handshaking, and I'm having problems with reliability. Basically the nRF51822 crashes and...
Hi, I've got a pretty basic question, but I haven't found a satisfying answer for it. It is obvious, that the CC registers are 32 bit wide, but because the RTC Counter is...
Hello:
Does the nrf52 radio peripheral EasyDMA write to PACKETPTR on byte boundaries or does it write "bits"? Suppose I have the ADDRESS_BCSTART shortcut enabled and the...
Hi all,
I can use the API sd_ble_gap_rssi_start to start RSSI and can get the value when the BLE_GAP_EVT_RSSI_CHANGED event occurs.However,when I use the sd_ble_gap_rssi_stop...
Hi, I'm recently concerned with the latent risk that nrf51822 might be hacked by extracting the firmware also known as "snarf"ing.
And I know there is Memory Proection Unit...
I followed the guide of github.com/.../nRF51-ble-bcast-mesh to try the mesh with NRF51822.But there seem no discribtion about which softdevice we should use.I loaded the s110_nrf51822_7...
Use SDK6.1 / SD7.0, iOS9 can not pairing!
dm_ble_evt_handler() return error "BLE_GAP_SEC_STATUS_UNSPECIFIED"!
It is the captured packets file: ble_proximity_ios9.1.pcapng...
I can't find an implementation for the indoor positioning service in any of the SDKs. Should I assume it's not implemented? If so, are there any plans to implement it?
...
Hello,
a presentation given at the nRF52 Global Tech Tour stated that one of the planned features for S132 and S130 was a support for multiple peripheral connections (2...
Hi
Now I'm using the S130 and ble_app_uart.I meet some problem need your help.
Firstly,I download the code to PCA10028,then it can connect to nRF UART on the iPhone5S...
Hey,
I am a bit confused with "client characteristic configuration" that is used to enable notifications (at least in Android).
To enable the notifications I have to...
The manual for my Agilent N4010A Wireless Test Set talks about a BER test based on a "vendor specific loopback test mode". This mode would allow me to do BER measurements...
