Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
I've got a custom board fitted with an nRF52832. Am running NCS v2.6.0. Operation involves:
1. Being in System On idle with all peripherals disabled to keep current to a...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hello:
i'v try v2.0.2 and v3.0.0 and v3.0.2. got error as follow:
or
sometime install toolchain got msg " Failed to fetch available toolchains. "
what the url...
Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi all, i am experimenting on the example "ble_app_beacon" on my smart beacon kit, but i have two questions about it (though they are pretty general):
When a connection...
Hi Experts，
I use TIMER_1 and PPI to driver a 'H' style bridge for our motor. Unexpected system reset will happen if I trigger the 'H' bridge PWM with ble connected. It...
Hi,
I run the code of the radio_test example in a VisualGDB project. When I start it with a debugger connected, VisualGDB informs me that a ARM semihosting system call...
Hi, is their any brief explanation for nrf5-sdk-for-eddystone project firmware newly released by nordic. I go through the project but it is very hard to understand can any...
We have an use case that we may need to support up to ,say 500 sensor nodes and it may be added or removed dynamically. And we should collect all sensor data within 3 seconds...
Hi all:
Based the descriptions in data sheet, the GPIO9 and 10 are set to NFC antenna pins by default.
And I cannot control these 2 pin correctly by configuring the pins...
I want to use NRF51822 to advertise is door close/open. No need bidirectional data sending.
Only one way from NRF sensor to mobile phone app.
Actually I have only two different...
I am using NRF52 S132, and using UART service , but my phone is getting disconnected automatically after 1 or two minutes. I have seen this question asked in Forum but that...
Hi,
Has anyone test with Nexus 5X ?
I could not change connection interval 7.5ms, the interval is always 45ms.
Does anyone know how to change the connection interval...
SDK 9.0, examples/ble_peripheral/ble_app_hrs
Trying to use DFU with a bond device, I got aware, that after the update, some "static" data seems to get corrupted during...
In the Keil Pack nRF_Libraries V3.10 [SDK V10.0.0?] (Low-Power PWM Example)
Not a big Bug, but an inconvenience all the same.
low_power_pwm.c line 165
ret_code_t...
Hello,
I want to change the advertising timout during runtime. We have two use cases for our device:
Batterie mode --> advertising timeout = 2min
Power...
Hello,
Implementing a LED led driver was pretty simple and below code works well:
nrf_gpio_cfg_output(LED_PIN);
nrf_gpio_pin_clear(LED_PIN);
NRF_GPIOTE->POWER =...
