Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
any plans to release firmware package for nrf51822 smart beacon using Soft device 8 and SDK 8? Thinking I better ask before I start adapting it on my own.
thanks...
What is the pinout on the DEBUG OUT-pins?
How do I adapt the code to work both with dev board and an external chip?
There are BSP stuff I probably can't use that I use for...
I am using S110 7.1.0 which I know has the ability to unblock the CPU during Radio Event. However I would like to do the opposite and increase the time between a Radio event...
Any news on the new specification for S130?
I am trying to find out the concurrent power profile. It the power management section it said that it has not be characterized...
Well, I've ordered my preview nRF52-DK and might get it by the weekend. I have not been able to find the schematics and design files on the main Nordic site, or the new infocenter...
This project is a HRS example from latest SDK, without any modification. I use nrf51 DK board. WHen I debug, I get hardfault after some type. Try to run the code under debugger...
Hi,
we used NRF_UARTE_Type POWER for the "peripheral power control" of the UART interface on nrf51 - works fine.
After trying to port the nrf51 to nrf52 I found out...
The question is: how to completely turn off PWM in SoftDevice?
I am using the libraries nrf_pwm.h and nrf_pwm.c in this repo for PWM with SoftDevice. Everything seems to...
Hi,
when trying to update the firmware with current nRF Master Control Panel (version 1.10), the update finishes successfully, but the firmware does not run.
The problem...
I've tried a trivial example (blinky-like, compiled by gcc using proper startup and ld scripts) on nRF52 devkit, but I always only get hard fault.
Debugging through the reset...
The nRF24L01 dataseet V2 (the most recent I think?) states (p.23) that the nRF24L01 can operate on frequencies from 2.400GHz to 2.525GHz . The channel steps are stated as...
I am completely confused by the nRF51 UART. I'm trying to port code originally written for an STM32 (another cortex chip). There, I define an interrupt, enable the RXRDY or...
Hi,
I need to have two different interrupt handler for one pin?
For LOTOHI one handler and for HITOLO another handler, how to do that?
Here is what i did until now...
