Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
I've added a custom service and a few characteristics on the nRF51822. How can I access the current value stored in one of those characteristic outside of a BLE event occurring...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
Hi,
My application uses the softdevice 110.
Everytime, there is an event on my sensor. The sensor sends the event to my pin, which generates a gpiote interrupt . But, the...
Hi,
I'm trying to determine why a HCI DFU upload fails.
There is a log of the communication below showing the serial request/responses on the Windows side.
Is anyone...
Hi: I use dfu_single_bank_hci to update application. HCI_SLIP_UART_MODE = APP_UART_FLOW_CONTROL_DISABLED, HCI_SLIP_UART_BAUDRATE = 38400.
I use command " E:\hci_dfu_send_hex...
Hello,
In my quest of working with pstorage_raw.c I found an annoying situation when I tried to clear small portions (as I thought by using raw I would have full control...
Hello!
I have based myself on the ble_app_uart example, taken out the UART bit, and all that remains is the bluetooth functionality.
I have also implemented SPI communication...
hi guys, :)
I used SDK 6.1.0., Softdevice version is S110_nRF51822_7.0.0.
I compiled the template project. (in the "C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310...
I want to use the UART to get and send data to another MCU on ble_app_beacon of SDK 8.1.0.
But after I add the UART function to the project, the UART can't work.
Can the...
Thanks for the SDK 8.1.1 fix. Please make it available also as a .zip in developer.nordicsemi.com/.../
Currently the fix cannot be used with a GCC toolchain as it is only...
Hi,my friend
I use the nrf905,At one end Use the PCB antenna, on the outside part of the metal.Using the results, said communication distance is shorter than 40 meters, easy...
Hi,my friend,
I have been using nrf905, but its performance is very bad.
Have a compatible chip nrf905 data communications? Working frequency 433 MHZ,100 KBPS baud rate...
uart_fsm and proc_fsm never get called.
debug on the first line of the uart_fsm and proc_fsm are do not come even
gpio toggling stops once uart interrupt received. I am...
