Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello, I am asking for your help again.
I just managed to brick the chip that I am working with. The problem is that I am not able to erase or program the flash. However...
Hello,
I have not found a lot of information on connection encryption. I want to use a preprogrammed Long Term Key in my mesh that is then used to establish subsequent...
This is the application file I am trying to download:
dx02.zip
This is the sniffer Log I just captured by wireshark
dx02_20150820.pcapng
I was able to upgrade firmware...
We have a heavy duty scan based application being built on top of the nRF51822 SOC. We have tested the scan function (S130 SD) on both a custom PCB and also the Nordic Smart...
Hi,
I have PCA10028 board, and I'm trying to implement UART send/receive.
I've searched for the problem here but could not find a solution for it.
My uart init function...
Hi
I'm using Keil V5 to program the Nordic nRF51 DK ( the one here: www.nordicsemi.com/.../nRF51-DK) but I'm a bit confused as to whether or not I need to change the settings...
I am not quite certain what the advantages/disadvantages are of using LDV vs DCDC if you are using an external regulator. In my case i use a LiPo battery outputting ~4.2V...
In the ant-to-ble bridge example in the 7.x.x SDK, there is the following comment in examples/multiprotocol/experimental_ble_ant_app_hrm/main.c :
// Need to close the ANT...
Hi all,
As I know in constant latency mode, both the regulators (1v7 & 1v2) and HFCLK are kept on. Is there a way to keep the HFCLK on while one or both the regulators...
Follow up this image. I want to reduce the negotiation time.
10:44:43.655 --> Connected to D6:9E...
10:44:45.123 --> Services Discovered
= 45.123 - 43.655 = 1.468...
when i test the ancs example application for nrf51822, i foud a question : after i disconnect the lightblue ios app with nrf51822 peripheral, the iphone still connected with...
I downloaded ble_app_lbs from GitHub. Loaded the project (on GitHub it was saved as a MicroVision 4 project) into MicroVision 5 and build with no errors or warnings.
I...
Hi sir
I want to combine heart rate, proximity and uart(proprietary) projects to one project.
As your experience, is it possible? Any side effect for that? Thanks.
J...
I have an NRF51 board running as a GATT server. Using an iOS application (LightBlue) I connect to the NRF51. If I quit the iOS application then I get a disconnect event and...
