I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
I am using RedbearLab BLE shield V2.1(nRF8001). I am connected once, i received the data. Now i want to terminate the connection and want to start advertising again? With...
i've got problem with spi master connection, im trying to set leds via SPI on DWM1000 module, i've checked through advertising that spi_master_send_recv() sends correct values...
I need to keep track of an integer array in an nRF51822 BLE peripheral (SoftDevice 8.0.0) between power cycles, and I try to use persistent storage manager for this task....
Hello,
I'm starting a new project on mbed with nRF51422. I'm a little bit lost about how to modify nRF51822 project to use S310 (ANT+ and BLE) package instead of S130 ...
I'm developing a BLE application where I want my slave/peripheral to sleep as much as possible to save power. I'm not sure how to set the connection parameters.
I'm looking to migrate from SDK 6.1 to SDK 9.0, using GCC and Eclipse. Any pointers would be welcome.
Also, I'm hoping to start using the OTA DFU. Once again, if there are...
I want to capture connection packets between BLE Master and Slave
(this part is easy) but also capture any advertisement send out by slave
at the same time.
Our BLE peripheral...
I brought up the Template example on the S110 for nrf51822 and as an exercise, attempted to add in the battery service. I just did a few simple things:
in main.c:
-included...
Hello, I want to using nrf51 dk with uart communication.
So, I want to know how connect both PC and nRF51 DK.
I've download with 5pin connector to USB.
In former days,...
hi,
i have meet an issue,when my pca10028 board was advtersing it can be found by the android app which provide by nordic.But it can not be found by my mobile phone.So,i...
I have compiled the bootloader and the application firmware with keil.
When I install the application firmware by means of the bootloader dfu ota.
The bootloader launches...
Hi,
Unable to locate the source code for "UART/Serial Port Emulation over BLE"?
The documentation for this is available in this link - developer.nordicsemi.com/.../a00072...
Hi, i try to understand how to use power down modes. But i have a problem in the example gzll_device_w_power_management of nrf24le1 sdk. Before enter register retention in...
I just started using RTT because I needed to trace execution through some ble events and the uart could not keep up.
It is very nice, but I am used to frequently resetting...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
