Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello,
I`ve got a working S120 peripheral BLE device with custom services and characteristics.
I am able to connect and bond with iOS and Android. But I cannot connect...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
My nRF51 will occasionally lose connection to the computer, and I have to disconnect and then reconnect it before it will work. How can I reset the device dynamically, without...
I'm trying to compile a project I have for nrf51 on nrf52. I am running into errors with macros not being set.
For example:
error: #20: identifier "ADC_CONFIG_RES_10bit...
Hi,
I'm working on a sensor application that sends out fairly large quantities of data via BLE notifications. I understand how bluetooth works and have read and followed...
Hi,
I'm currently testing ble_app_uart on nRF51822 custom board. I connected it to nrf51 DK P19 and was able to program the hex file successfully.
But it doesn't run...
Hi, In your documentation you specify the maximum CPU temperature 85 DegC.
What problems could one expect after this point?
How much safety margain du you have on this number...
I'be been reading over and over the datasheet but cannot see how to dissable Enhanced ShockBurst features for my application which only requires basic one way radio.
I...
Hello,
I'm trying to program that module, but i can't do it correctly.
I'm using a program that works fine in nrf51 DK, but when I program this in ptr5518 my smartphone...
I want to port either the S210 experimental DFU over ANT_FS to serial DFU or the S110 dual bank serial DFU project to be S210 compatible.
I'm using S210 V4 and SDK 8
...
I would like to connect more than 8 devices to a single host. Therefore I would have to set the same role to multiple devices.
What are the implications of using the same...
HI,
I have some problems with the function sd_ble_gap_scan_stop(). I want to stop scanning into the RTC1 event handler but when I use this function (sd_ble_gap_scan_stop...
HI:
i have a question.if i use 51822 to connect other ble(ti or csr) ,could that be achieved.i have used ti dongle to scan 51822,but can't found 51822 device.if 51822 connect...
