I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
I made an app based on this tutorial on SDK version 11. But now I have to use the latest version 13. Everything changed. Is there an easy way for me to migrate to version...
Hi,
I'm in the process of evaluating the nRF52 for use with a Windows application I'm building.
I was able to setup a Central + Peripheral using nRF connect and this...
Hii this is vinu .iam trying to develop health thermometer service for central but iam facing problem in indication for specific measurement characteristic.and iam using cypress...
I am creating a BLE peripheral device and I am using peer manager in it. What is the maximum number of peers that my device can bond with? And what will be the result when...
The basic question is: if I initialize the SD and then forcibly change the priority of the WDT IRQ to zero via NVIC_EnableIRQ(), will that cause a problem?
I know you don...
Hi, We are using NRF52832 in our application. Can you please suggest swd interface module for programming NRF52832?? or tell me any cheapest way to program NRF52832??
nrf51 SDK9.
On peripherial one service has static passkey and it connected to another device on central nrf51 without problem.
I added sec open batt service on peripherial...
I want to undestand this. I can't see any examples with it. In the example ble_app_proximity I always received 100% level.
If it possible, can anybody give a ADC config example...
I am working with a Blend Micro Board (Arduino IDE with RBL_nRF8001 sdk), using
Evothings.
Using the RedBearLab Simple control example I can easily connect to the board...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
Hi all,
I measured the delays between a GPIOTE event and a Task (in this case toggling with another GPIOTE) through PPI.
The results are showed below:
For the...
Hello, I followed from the link . I successfully program bootloader, and bootloader setting and program. And my program is working fine.
But I cannnot update from DFU. Everytime...
Hi,
I am working on with nrf52 with SD132 v2 SDK11 since we need serial bootloader.
I tried a gattc long write sequence to write 22 bytes. Everything works well, peer...
