I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
I've been through the tutorial of connecting the NRD52 board to my PC, but my PC isnt recognizing it at all. No pop up for any usb devices. I've tried different cables and...
Dear Nordic Team,
Thanks for supporting.
currently i am try to interface MMA8453 accelerator with ble proximitty example .Already i have interfaced peripheral example...
Hello, I am new to NRF. and actually i dont have other MCU experience, beside adrduino.
my question is not about BLE/BLE+,
it's more about how to use NRF5283 in keil question...
SDK 13 Alpha
The header guard in serialization/connectivity/codecs/s132_s140/serializers/ble_l2cap_conn.h looks like this:
#ifndef BLE_L2CAP_CONN_H__
#define BLE_L2CAP_CON__H__...
Hello,
I really like the new nRF52840, especially it's Bluetooth 5 capabilities. The thing is that i cannot figure out if i would be able to make nRF52840 based devices...
Hello,
I have tried to debug ble_app_uart_pca10040_s132 application included in nordic SDK12.2 with Segger Embedded studio v3.12, but even though I don't get error while...
I have been working on an application for iOS for a few months now, and I want to give my users the best experience possible, when it comes to the peripheral I intend to use...
I would like to test the Fatfs demo using a target spi flash memory chip. The example code calls out sd card fatfs driver. Can I assume that spi flash memory is the same as...
I'm building a software for the nrf5822 using pc10028. I'm using CMake and after following both morf.lv/modules.php and devzone.nordicsemi.com/.../ I successfully made the...
Hello Noridc,
Liking your solutions, and I appreciate the thorough documentation.
Working on layout and so I was looking carefully at your reference design Gerbers for...
Peer manager worked fine for bonding on my pca10040 board. However, when I flashed the code to my prototype, built with a SparkFun nrf52832 prototype board, I received PM_EVT_ERROR_UNEXPECTED...
