Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hello all, i made a board with this BLE chip:
nRF52832-CIAA-R
What happens is that when i enable power supply i can see the circuit is properly in advertise ( i can scan...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
I am developing a project using the nRF54L15 DK to interface with an ST25DV64KC NFC tag (specifically the Class 3 or Class 6 daughterboard from the ST25DV64KC-DISCO kit)....
I have a project migrating to nrf Connect from ESP-IDF. We need to recreate a system to work with existing devices on BLE Mesh, but I am having trouble figuring out how to...
Dear colleagues, I am using the Nordic nrF9151-DK as part of assignment 2 of the intermediate Devacademy course. This assignment is about trying and using the various vscode...
Hi,
I'm using nRF5_SDK_12.0.0_12f24da and s132_nrf52_3.0.0_softdevice to do the mutilink and it's almost ready. We want to do the OTA on it. I think the mutilink is working...
Hi there,
It isn't obvious from the reference layouts on the downloads page for nRF51822-CFAC if the ground plane is supposed to create a 50 Ohm trace going into the balun...
Hello everyone, i have a task where i need to transfer 50-100kB of data from ble peripheral to a central device. I have read many posts here and i have a pretty good idea...
Hi, I work with the nrf51-ble-driver_win_0.5.0. I changed the heart-rate-collector to discover the characteristic of connected devices. Maybe I'm blind. But the ble_evt_handler...
I want to accomplish something very simple: use a timer to output a continuous square wave on a certain pin, at 30-60kHz or more. It doesn't have to be PWM or anything fancy...
Hi,
I'm working on a BLE application which use ECC.c (Elliptic Curve Crytography). The problem is Keil has found an Error:
._build\nrf52832_xxaa.axf: Error: L6218E:...
Hello Support Team,
I am developing a BLE project use of nRF52832.
My work base on SDK 12.1.0, I have research these workflow, I find that are 3 channel radio when RSSI...
HI
I'm trying to connect a heart rate sensor to nrf51822 but I cannot find a suitable sensor. Could you please recommend a heart rate sensor which nrf51822 can support...
I am using nrf52832 with softdevice s132, it use the power manage function to enter to the sleep mode.... But i cannt recognize whether it is in sleep mode or not.. Can anyone...
Hi,
I am trying to port pca20006 smart beacon kit code to pca10028.
I have attached main.c --> main.c
I am currently using following ROM and RAM configuration for pca10028...
I want to know that how to judge the Traffic block.
If there are 1 BLE and 1 android APP. It must be ok.
if the number is 2,3,4,5....n
What is the maxium n?
How to cal...
Hello,
I am using a custom board and my setup looks like this:
nrf51 chip
16KB RAM
256KB of Flash
external crystal of 32MHz
SDK12.1
Compiling on Linux...
Hello,
I am trying to read values from MPU9250, I can read them from accelerometer and gyroscope but when I try to read from magnetometer i cant get any values on UART...