hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am working with nrf51822 MC. In my Transmitter code, i am using in low power mode. I was enabled the low power in my code (__WFE(), __SEV(), __WFE()). I measuring...
Hello, I need HID device with NRF51 Dongle.
when NRF51 Dongle insert PC, PC will check it as HID device.
So, could anybody can share suggestion how to add HID on NRF51 Dongle...
Briefly:
Is it possible to switch LFCLKSRC to the internal RC from Xtal with WDT or RTC running? It appears I am only able to do this when Xtal is generating LFCLK...
I am trying to build a ibeacon device, but when iphone in "background mode", it can not get data from ibeacon device.
I used test code :examples\ble_peripheral\ble_app_beacon...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and Master Control...
On the product page: www.nordicsemi.com/.../nRF-Connect-for-desktop
The link from the ' Documentation ' tab is: infocenter.nordicsemi.com/.../nRF_Connect_intro.html
...
Hi,
I have done BLE tutorials [BLE Advertising, Ble Services and BLE Characteristics]
With my NRF51-DK was working perfectly the example of BLE Characteristics (with...
Hi,
I designed a pcb using nrf51 chip with some sensors,
this pcb should read ,every minutes, all values from sensors and saves them into the flash memory beside that...
Dear
Now, I need make one nrf52832 board as USB Dongle, it can be HID device by checked from PC.
And, nrf52832 should support esb protocol, now for esb, I know something...
hai
i was started a bluetooth based project. So i have started with a blend micro.But the range of communication was very short.So i have chosen ble nano with TX power...
Hi
I am calculating the power consumption using
devzone.nordicsemi.com/.../
But there is some point that I don't understand.
When the BLE event type is "Peripheral...
Hello,
the past week I am trying to make the bootloader_secure example work for a custom hardware with no luck. This whole procedure give birth however to several questions...
Hi
I am currently working on a BLE based hardware but I am a little confused about the terms such as service, characteristics... etc.
Let's say, I would like to control...
