Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
Hello,
Is there a way to temporarily disable bonding and just allow any connection? I want to generally use bonding, but there are certain corner cases where I need to...
Hello,
I want to use the FDS libraries in order to store some data into nrf52's flash in my application and I have a bootloader to allow secure dfu by ble.
I manage...
I'm struggling with current consumption. I need my device to completely sleep and leave only the RTC on when the ext power is off (run on battery). After making sure my RTC...
Hy everyone!
I'm trying to write a non-volatile memory position of a device via I2C (twi), the device, a flash memory is the slave.
In my application, I have configure...
Hi I am using the SDK 12 and I am doing some test using the experimiental_app_ble_blinky central and peripheral parts.
I see in this example it use boolean values to indicate...
Hi,
I am using the experimetal app_ble_blinky on both sides peripheral and central.
I edited the peripheral characteristic sizes to 4 and I am able to send notification...
I am trying to modify the default mbed bootloader to include support for watchdog.
I'm running with nRF51822AC (NRF51DK).
My program is written with mbed classic (uses S130v1...
Hello
I got this nordic nrf24l01+ module and trying to interface with pic18f25k22. this is my code. tried lot but unable to communicate (receive any data). I'm able to...
Hi!
Does someone tested the range of newer NFR24L01+ module with external SMA Antenna?
Any result?
As we are looking for a module with a range of ~1000m line of sight...
Hello,
I only recently discovered Nordic Semi and I'm looking through the various products. I'm wondering what Soc offers the lowest link latency for audio, seems like 2...
Hello,
In my application I want to switch between using bluetooth low energy and enhanced shockburst (esb). I have tried using the timeslot api to run both of them together...
I am using the nrf52832 with its Development kit to transmit trough UART to the PC a frame with 26 bytes, I have configured the port to 1MBoudRate. Once I prepare the frame...
Hey guys,
I followed this guide and successfully synchronized the timers from two devices(nRF52 DK). But if I let these two synchronized devices keep running all the time...
