I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
i think your nrf51 iot sdk don't have rpl functionality....
if i want to implement rpl on it what is the procedure...
if i want rpl on raspberry pi what is procedure......
i have bluetooth usb 4.0 dongle..which part of bluetooth stack it contains...?to support simultaneous master and slave connections will it need any firmware update...?
...
As we known we can set static passkey in peripheral side (s110) with the API sd_ble_opt_set(BLE_GAP_OPT_PASSKEY, &ble_opt) as below:
inline void setPassKey(void)
{
uint8_t...
I've tried all 4 versions of the HID Mouse Example provided through the Keil Pack Installer tool and can't seem to get any of them working.
The code compiles and downloads...
I was trying to compile the example code(nRF51 SDK8.0) for ANT and flash to my nRF51DK(pca10028) board, but the example code was not working on my board. I tried compiling...
Hello.
I'm now writing a software based on nrf51_sdk_v6_1_0/nrf51822/Board/nrf6310/s110/ble_app_hrs. The SoftDevice I'm using is s110_nrf51822_7.1.0_softdevice.hex. Why...
So I've been using a user submitted SD safe TWI implementation that I found here. This has worked well so far, but upon updating to SDK 8.0.0 parts have broken. Now when I...
Hi,
I'm using the NRF51DK which comes with the nFR51422. I initially flashed the board using the ble_uart example.
Since then I've tried flashing it with other examples...
Since we have some performance problems with sd110 V7.0.0, we tried a upgrade to v8.0.0.
This version(8.0.0) with IC revision 3 solved our performance problems:).
But a...
Hi,
I am working on a project regarding a portable device for healthcare monitoring. This device will have a nrf8001 module integrated that will communicate with a iOS...
Hello there,
I know that the range of the possible BLE communication depends on the internal configuration as well as on the external environmental conditions.
I would...
I downloaded the zip file from Git Hub Nordic.. and extracted it into C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\7.1.0\ble_peripheral\
When I open the project...
Hi~
I have a nrf51822 EK board(PCA10001 V2.2.0), but the J-link OB can't flash 51822 chip.
The situation is:
1.I can see Segger J-link on segger software&nrfgo studio...
Hi all,
I've been trying to get a new Win 7 (x64) PC setup with with the Nordic dev tools.
Studio, MCP, SDK etc.
I've installed Studio (1.17.1) and MCP (3.7.1). This...
Hi...
i have downloaded latest SDK zip file "nRF51_SDK_7.2.0_cf547b5.zip" from developer.nordicsemi.com/.../ but i could find mdk file "nRF51_mdk_6_1_0_installer" only...
