Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
Hi all,
I used the ble_app_hids_mouse example in SDK 4.4.1 and found:
1.when the mouse does the first bonding with the master, the report rate could reach 125Hz(I set...
Hi, I am trying to code my nRF51822 on my custom board, however right now I'm having my doubt on using some of the example code provided in the SDK.
Essentially, I want...
Hi,
1/ I download the s110 softdevice and ble_app_hrs to the nRF51822 board, and running normally.
2/ I download the s120 softdevice and ble_app_hrs_c to the nRF51822...
Dir sir. I read the white paper "Tuning the nRF24xx matching network" and I have a question.
I would like to know the setting of the spectrum analyzer when I measure the...
I'm looking at the 5.2 SDK and I have noticed a few minor things that may be bugs or might be my mistake but here goes:
In the GCC linker scripts, I was carefully...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am working on a keyboard project,I change the HID report as follows
0x05, 0x0C, // Usage Page (Consumer Devices)
0x09, 0x01, // Usage (Consumer Control)
0xA1...
Hi,
How does the advertisement filter policy work?
I tried both BLE_GAP_ADV_FP_FILTER_SCANREQ and BLE_GAP_ADV_FP_FILTER_BOTH, but this doesn't restrict other devices...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I just purchased an mbed developer kit and I am looking for the source code for the device. I want to write an iOS app to interface to this device via BLE. I'd like to have...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Using ble_app_hrs running on a PCA10004 (nRF6310 motherboard + PCA10004 which uses a PCB antenna), the achieved range at +4dbm (<10m) seems to be short. Master Control Panel...
I think the new MCP might have a bug somewhere. I have not been able to find out the exact sequence on how to provoke it, but I have to restart the application more often...
if I set BLE_GAP_CONN_SEC_MODE_SET_OPEN, I can get data,
but if I set BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM,
Three different even sequences happened, only one sequences...
