My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I Just upgraded my RTE to the latest two minutes ago, and tried an RTX example.
The example compiled OK, But in RTE manager, it is showing missing component.
Screenshot...
Hello!
I'm in doubts about proper configuration of GPIO pin, which I'd like to be able to reset external device (DWM1000), connected to nRF51 by SPI.
The datasheet says...
Hello,
I’m working on my own custom board based on the nrf52832 (QFAABB).
Here the schematic:
I succeed to flash the board with the nrf52DK (PCA10036) via the debug...
Hi there - new to Bluetooth but have an interesting question.
Is there a way to have multiple users connected to the same Bluetooth connection to stream music? For instance...
Hi community,
I am working on IoT device. We want to establish a secure connection therefore we are going to need a secure storage for our private key. I am aware that the...
Worked fine until yesterday. Board turned off with computer, also the power switch on the board was in off position before turned on this morning. Now the debugger circuit...
Hello Nordic Team,
Please, I would like to ask some questions about BLE based smart-phone accessory.
Actually, I think about using a BLE based accessory (for instance...
Tuning the nRF24xx matching network:
The balun-function is done by the
180° degrees phase shift in L1. This
causes the signals from the two ANT
pins, 180° out of...
I am sending IMU data as 20 byte packets through nus service at the rate of 50 such packets per second. The device is a nrf51 DK configured as ble peripheral (S110). The application...
Hi all,
I have a makefile which runs perfectly from the command line on Windows under GCC, but in Eclipse it fails with this message in the Console:
make flash
make...
My application had a ID to separate difference device & host for the communication in the same area. When the Host power up, it need to search any existing same ID Host nearby...
Hi ,
I want to set the channels used for exchanging DATA (after connection) when peripheral and master are connected.
i searched and i find that it's like this :
//Set...
Hi I'm using the PCA10003 dev board to try it out the OTA firmware update.
What i did is exactly that:
Modify the bootloader example for S310 softdevice and 10003...
Hi, I have been developing with the nRF52 DK for the past couple of months however I have encountered an issue today which I am unable to resolve.
I am unable to establish...
Continuing my mission to have SES set up to be the complete development environment on a Mac I am struggling to get the Jlink Debugger to behave with SES.
It appears I...
