Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Is it the only way to call a function on a read characteristic to make a read request and then inside on_ble_event call the function?
Is this the right way?
Hi
in the communication with an SPI peripheral device, a communication cycle might take up to 5 ms.
It is implemented as a blocking function, meaning that app_sched_execute...
Hi all! Several weeks I've tryed to implement code for my wireless temperature sensor based on nrf24le1 and ds18b20. In datasheet said that in memory retention mode the power...
Hi,
Is it possible to send a advertisements for a single (or a fixed number of) Advertising Events? I need to control the number of Advertising Events "sent" for a mesh...
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I understand that in order to trigger bonding procedure you need to read/write a secure characteristic.
I am using the nRF Connect application on IPhone and trying to see...
Hi all,
I need to take samples of a period of two periodic signals and made some DSP processing with both signals.
I need at least 64 to 128 samples per signals.
I...
Greetings,
In Bluetooth 5, there is a new mode of advertisement called periodic advertisements where the advertising device can periodically advertise over the 37 non-primary...
I have a design running on nRF51 that I'm evaluating to run on nRF52. One important characteristic I'm looking for is to store it for long period with a minimum power consumption...
Having some problems upgrading the PCA10056 to firmware 1.0.1 as stated in the getting started. After downloading the only file I found I can no longer connect to it.
Can...
I've been trying to use nRF52 (PCA10040 board) with SDK 12 to read data from max30102 through I2C.
I used non-blocking read and this is twi init function and event hander...
According to S130_SDS_v2.0, I can choose to return NRF_RADIO_SIGNAL_CALLBACK_ACTION_NONE after NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_SUCCEEDED to stop extend more timeslots...
I want to trigger SAADC by PPI between RTC compare event and SAADC sample task. Is it possible?
In the SAADC example (SDK 12.2.0), a timer is implemented. In function nrf_drv_timer_extended_compare...
Hi!
Which project do i need to look at in order for 5 devices which are NFR52 to send data each other
There is only one center in multilink project and other devices dont...
