I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello,
I am using the following function call to set up PWM:
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(5000L, BSP_LED_0, BSP_LED_1);
However, the compiler...
Hello,
I designed a board with a nrf51822 on it. My problem now is, that this chip needs far too much current (with no firmware on it) when I apply the 3V3 power to it. I...
I have been working on a project that involves two nrf51 dev boards, one is acting as a central and the other is acting as a peripheral, and I have been encountering a problem...
Hello!
For beginning with nRF51 I chose BLE Nano set of boards (BLE Nano + MK20 USB donbgle) and it was of great help to easily begin with BLE.
So far, we came to the need...
As an experiment, we want to implement soft power off for nRF52 with external components. We want to keep the entire circuitry entirely switched off, and after a press of...
I do not use board.h nor bsp* in my project, and also I am not initializing the pins that I do not use in my program currently - so P0.17 is not initialized and setup. However...
Hi all,
I am new to nrf51-dk and I am using nRF5 SDK v11.0.0.
I wanted to perform the task below.
When the DK is turned ON, read on board push button status.
If button...
We are implementing scan functionality in nRF51. I would like to understand if anyone has tested or tried to scale this functionality when there are thousands of beacons around...
Hi everyone,
I was wondering how GAP calls and events are synchronized within the SoftDevice.
Example:
// conn_handle is updated in the CONNECTED and DISCONNECTED...
The Android Master Control Panel app has an option to remove bond information (which works). But the API for it is hidden .
I'm just wondering if you use reflection to...
We are trying to replace an existing solution that uses a custom Service with 4 Characteristics. Unfortunately none of those share the same base UUID.
Basically the Service...
Ok - I'm trying to get my arms around this bootloader process.
I am using the nRF5_SDK_11.0.0_89a8197 SDK along with the PCA10040 develeopment kit.
I also am using IAR...
I'm trying the run the smart remote 3 v1.1 firmware built using IAR.
The firmware fails to init the touchpad and enters a forever loop.
The program only builds with optimization...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0. In my application i plan to use RFX2411N PA/LNA module. In datasheet of RFX2411N, I found that it can be used in...
