Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello everyone.
I want to increase the operating range for nRF51822. To do this I added PA SE2576L in design.
Unfortunately, I do not have experience in RF develop...
Hi,
I'm attempting to use Version 2.1.0 of the HomeKit SDK on an nRF52. We're using the s132 SoftDevice 2.0.0-7.alpha (the SoftDevice in the latest nRF5 SDK v11.0.0). ...
Hi.
So my problem is, that i cannot successfully program external board with preprogrammed nrf51822 chip in the board.. This board is from china.. its an ibeacon.. If i...
I've recently been playing around with Bluetooth Developer Studio, and I can see it's potential despite it having a few annoying bugs.
I've set up a custom service by re...
Where would be a good place to feed a watchdog when using a softdevice?
My first guess was in main loop:
for (;;) {
NRF_WDT->RR[RR_number] = 0x6E524635;
power_manage...
Hi,
When a watch dog timeout occurs, I want to save some data to the flash memory prior to reset (namely the RTC count value). Therefore I enabled the wdt interrupt. The...
Im using nrf51, I configured the watchdog to reset after 3 seconds of hang and it works. But I have absolutely to save some data in flash before reset
Is there anyway to...
My custom profile was being built fine until I added a couple of standard descriptors to a custom service characteristic. Any idea what's going on here?
19:34 - [Code Generator...
Hello All,
I want to develop bluetooth mesh using NRF51.
I have question about this:
Is their library closed or not?
Do we need smartphone like in CSR?
...
Hi, I have a TinyShield Nordic module and I am having some troubles trying to customize the advertising packet. I have downloaded NRFGO Studio and I have enabled service data...
I have an nRF 52 dev kit, an Asus router running openWRT, and an android phone with the master control panel.
I'm able to compile and flash the dev kit with the example...
hello,
I am using the nrf51822, I want to add a normal service which do not need bond before used at the ancs example.I hope it can do the follow tow points,firstly,if the...
Hi,
I tried to figure out what is happening on the lower Bluetooth levels but it is very difficult to find straightforward information. Especially the Bluetooth (4.2) standard...
Hi, My apologies that this seems repeat information from previous posts, however they do not give a clear answer to my question regarding 4.2 compliance. I must also state...
Hi,
I want to count the time in seconds for which I press the button and stop the counter when the button is released. How should I detect the long press of button and...
