I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Setting the gatts_enable_params.service_changed to 0 when enabling softdevice removes (or rather doesn't add) the Service Changed characteristic. That's what I want. However...
I'm developing a device based on an nrf52 chipset, and I'm experiencing strange behaving of the Radio interface. The firmware is based on SDK v11 and SoftDevice 132, the hardware...
Line 73 in function nrf_drv_rtc_init snippet bellow checks for UNINIT state. It accesses the m_cb array which is an uninitialized global. That condition would intermittently...
Hi
i buy a nrf51822-02 module and the chip of this,is nrf51822qfaah10
i compile the ble_app_uart_s130 and program my module but it does not have any advertising
my nrfgostudio...
Hello!
Does anyone know how can we send the multiple uint8_t MOSI signal to SPI and received the result on m_rx_buf?
Trying to send multiple bytes to "m_tx_buf":
...
Hi,
It is possible to use an non secure DFU in SDK 12?Like on SDK11?
How to migrate my custom DFU on SDK 11 to SDK 12?
UPDATE 1
it the dfu from sdk 11 I Get an...
When we use nRF5 bootloader provided with SDK the first application flashing must always be done using DFU over-the-air. Only after that it is possible to re-flash application...
Hello,
I'm new to Nordic nRF52 and trying to send commands via termial to nRF52. After receiving commands, nRF52 will use these commands to do i2c communication with other...
Hi,
I'm trying to simply toggle a pin with GPIOTE out toggle task from RTC2 CC0 event. Wrote up the following code and checked the registers in system viewer. Everything...
I am using S132v2 on nrf52831. I am using UART BLE application. I want to turn ON BLE meaning advertising and all parameter of BLE whenever i press any switch. Also bluetooth...
Hi,
I know this question must get asked enough, but i am at my wits end and have not managed to find a solution for this yet.
calling sd_power_system_off returns NRF_INVALID_STATE...
Hi,
After couple minutes of running my application catch softdevice_fault_handler with program counter set to 0x11150. Can you tell me what may be a reason of this error...
Hello community,
We have a requirement to do concurrent BLE peripheral and broadcaster roles with S132 stack. This seems to be one approach but a bit crude for our requirement...
Hello,
while reading the nrf52840_OPS_v0.5, I discovered, that there is a 32MHz peripheral clock. I did not found any reference to it in the rest of the document. Is there...
