I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi,
recently I experienced a strange behavior on the nRF51 chip, that is at a certain point some gpio lines remained held high, even if the firmware set them to low (both...
I clone the repository on GitHub, which is the accompanying code for the Application Note nAN-36 "Creating Bluetooth Low Energy Applications Using nRF51822", in the nrf51822...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards. I want to check my runtime. So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Hello all.
I am now making a central device to control a peripheral device.
The Firmware of central device is supposed to be updated by Smart Phone, like iOS or Android...
I'm currently making a device which use nRF52832 and that will integrate Capacitive touch feature. However, I'm actually a bit lost with this post: devzone.nordicsemi.com...
Hi, I use PCA10040 v1.1, Keil MDK 5.21a, SDK 12.1 with S132 v3.
I was using SDK 12 previously. The SDK 12 projects worked well.
Now I migrating to the new SDK. So...
Hi all, I'm working on SDK11.0.0 with softdevice S130 v2.0.0 and I need to update bootloader+application at the same time in single zip for these I created zip file by using...
I have a use for the pstorage module and while going over the implementations in the Nordic examples and libraries, I found a use-case of pstorage_register() in bootloader_init...
Hello,
I would like to use the PCA10028 close to the conditions of a future custom board at 1.8 V (including I/Os) but I would like to keep the ability to do source level...
I am using the 8.1.1 version of the SDK on a Rigado BMD-200 device, s110 version of SoftDevice.
The code has set APP_ADV_TIMEOUT_IN_SECONDS to the maximum (all bits set...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
