Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am planning to use the nRF51822 and the s130 soft device to manage data coming back bluetooth sensor nodes. It is likely that there will be more than 8 peripherals, although...
The SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does...
Hello guys
I tried to start TWI bus and got a lot of questions. (NRF51 1422 AC)
I added necessary libraries, could You tell me what more i need to include in my code ...
Hi , We are using NRF52832 for our product .I have a small doubt in using GPIO . Can we use PORT and PIN events simultaneously at a time .
I need to configure some pins...
Hi,
I have three beacons in my setup:
One listening (R1) and two transmitting (T2, T3). T2 and T3 transmit packets with same length.
Say, T2 has started transmission...
Hello,
My system is one device with multiple host, these host will connected to the device on irregular basis.
The host action are listed below:
scan->connect->write data...
hi, i'm going to do some project with nrf51822 and SDK 6.0.0.
i just made up ble connection between phone and the chip.
and i want to send data some fixed time periods...
Hello,
I think there's a bug in the app_uart library in SDK 10 that occurs when the FIFO is enabled.
Using SDK nRF51_SDK_10.0.0_dc26b5e, I was trying to write data to...
I'd like to control a DC motor using PWM (PWM0, pretty straight forward).
To determine motor speed I disable the PWM every 5ms (TIMER1, pretty straight forward) and measure...
Hello,
Our application consists of 100 BLE static centrals and 1000 BLE moving peripherals. Is it possible to hide our BLE peripherals to be visible only by our centrals...
Hi,
i'm testing an application on nRF52, with nRF5_SDK_11.0.0-2.alpha and SoftDevice 132.
I took the ble_uart example and added a custom service with some characteristics...
Hello,
i'm trying a bluetooth connection between nrf UART v2.0 installed on my phone(android 4.4) and nRF 8001 (i'm usign nRF2740 card). My microcontroller is a STM32....
Hi.
I made my own board using nRF51822AC.
I want to connect this board to PCA10028.
There is Debug OUT port(P19).
Net names are EXT_VTG, EXT_GND_DETECT, EXT_SWDIO, EXT_SWDCLK...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
Example code is using "ble_db_discovery_start()" function to discover peripheral.
In this function, there is "SRV_DISC_START_HANDLE...
