I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello Gentlemen,
I'm looking for sample code that shows how to enable security which prompts for a PIN number on the Android device when I want to connect to the nRF. ...
On the box for the nRF51822 there's one tiny sticker with nRF6815, Rev 2.2.0, 2014.15 and 10004490 written on it.
I can't find ohter information on the box.
Hi ,
i would like to know about
1)how to enable softdevice in nrf51288?
2) how to check softdevice is enabled or not?
can any one share information related to it...
nrf51_sdk_v5_2_0_39364\nrf51822\Board\pca10001\s110\experimental\ble_app_uart
runs ok when connected to Android 4.4 Nesus7 II
but will return error code 8 when connect...
Hello all,
I am developing application for evaluation board in which i am using 5 services. When I flashed my application on board it was unable to advertise. Then i checked...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I am trying to set up the WDT on a nRF51822, but the timing doesn't seem quite right. If I load the CRV register with a count of 32768 I would expect it to be a one second...
I'm new to Nordic devices and tools. I have experience with Eclipse but I was wondering if there is a guide to help with the creation of a brand new project under Eclipse...
Hi,
As have been discussed earlier there is a problem with iOS device losing CCCD values on reconnect or turning bluetooth ON/OFF.
A patch for the ANCS sample is presented...
Hello Gentlemen,
Is it possible to know the passkey before the BLE_GAP_EVT_PASSKEY_DISPLAY event?
my nRF sensor is set as a display only and my central is an Android...
Hi all,
we are using the nRF51822 together with another module that provides an 1.8V UART only (LO = 0V, HI = 1.8V). Other IC´s on the device are using 3V Vdd and are connected...
I would like to make two BLE single mode devices to communicate with each other and Bluetooth v4.1 supports that, I was wondering if any of Nordic's modules support v4.1?
