Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Does the lcd clobber the tmr0 and/or ANT ???
We just went through several days of working w/ ns on running ANT w/ RTC with a resolution of using sd_ calls.
Is the LCD...
Hi,
i am using nrf51822 custom board.
For our application i am using ble_app_hrs source code.
in that i have gpio interrupt for every 500ms, to get data from accelerometer...
For example, if I have a GPIO pin configured with low sense, and it goes low just before I call sd_power_system_off(), will the device return to System ON mode immediately...
Hello,
I've got a nRF51822 DK which I try to program with a SoftDevice using the nRFgo Studio (nRF51 Programming). My chip/programmer seem to recognized properly since...
Hi,
For developing our application i am using ble_app_hrs
in my case i have gpio interrupt for every 500 ms to get data from accelerometer.
question:
in heart...
Hi,
I am attempting to understand the timing of events when a mobile application connects to my nRF51822 based device. The reason being is that I have to enable the UART...
Hello,
Greetings, in the nRF24L01 datasheet, its mentioned that the module can work as a multiceiver, meaning 5 nRF24L01 module acting as PTx can communicate with 1 nRF24L01...
hi,
my customer using nrf51822 DK to have debugging software,the error occur in the attachment.
can you tell me something have Caused this problem?
thank you !...
I am using the code
err_code = sd_ble_gap_device_name_set(&sec_mode, (const uint8_t *)deviceName, nameLen);
I have made sure that nameLen is less than BLE_GAP_DEVNAME_MAX_LEN...
Hi
i am using twi_hw_master.c for i2c communication of accelerometer.
my accelerometer address is 0x18.
once i call
twi_master_transfer(0x18,dataW,1,1);
in...
Hi,
Can the value of NRF_RTC1->COUNTER be read safely from the main loop without first stopping the RTC or temporarily disabling the RTC1 interrupt etc? (nRF51822 or nRF51922...
I used the nRF51822 Evaluation kit and flashed the BLE_proximity example on to the PCA100001 board.
In the master control panel the USB dongle measured -46 dBm(Nordic_prox...
Hi all,
what if I want a sensor network in my house with BLE. Can I just install, for example, 16 nodes in my house and connect to all of them with one iPhone? Or would...
Hello,
I am currently using nRF24L01P with TI CC2591 in my RF module product.
I have a doubt that need your help to clarify.
Does the antenna impedance given in the...
