Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello,
I would like to stream sensor data from the Bosch IMU sensor over BLE at a maximum rate. I can collect data over I2C from the sensor but would like to know if there...
Hello to all nordic jedi masters out there!
I am using nRF SDK v11.0 with the nRF52832.
I am a little bit confused about the usage/meaning of the flag argument in the...
Hi all,
I am trying to send a large stream of bytes(60kb) to an NRF52823 using bbowl . BBowl exposes the uart through a TCP socket connection using noble .
I modified...
Hi,
In the schematic presented in the topic 17.1 (dc/dc converter, image below) of the nRF8001 datasheet it isn't shown that AVDD should be connect to a power supply as...
devzone.nordicsemi.com/.../
In this blog this is written:
"Opening and closing a connection event adds a lot of overhead"
how much is the overhead and where can i...
Hello,
I am currently developing a new bt-le-program and besides my own log-messages, I wanted to enable also the log-output that is happing in the files from the Nordic...
I'm building something based on ble_app_gls. However, I only want it to be pairable when I say so (user presses a button to put it into that mode). Is there a "correct" way...
Hi,
upon connection I get these messages via RTT:
nrf_ble_gatt:DEBUG:Peer on connection 0x0 requested an ATT MTU of 185 bytes.
nrf_ble_gatt:DEBUG:Updating ATT MTU to...
I would like to know how to dampen the effect of metal surface on BLE signal . Let me give you an instance, i am installing a wireless sensor inside a metal box and this sensor...
Hi,
I'm trying to make github.com/.../nrf52-spi-i2c-master-ssd1306 to compile with GCC (linux). So far I've managed to get it compiled, but linking fails:
mkdir _build...
Hi all,
I am using NRF51822 Bluetooth, which I am interfacing with the my microcontroller UART. when I dump the code into my Nordic NRF51822 BLE then it is only advertising...
Hi all, I have an Eclipse project in which I want to transfer packets of data bidirectionally between ESB and UART. The makefile includes both nrf_esb.c and app_timer.c (needed...
I'm working on a 2.4GHz wireless microphone (2T1R) project now. I'm wondering can I use nRF24L01+ as the core of transmitter and receiver? Also can it be configured into 2T1R...
So the question would be if I would need to pair each time the device comes out of reset or are there information stored to return to direct communication without pairing...
The chip uses nRF 52832. MDK keil μVision V 5.22.0.0 is used as the development environment.
The SDK version uses 13.0.0_04a 0 bfd.It is based on template_project.
1drv...
