Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
According to the documentation, the function sd_ble_gatts_exchange_mtu_reply() can return NRF_ERROR_BUSY , which would require the application to somehow defer the call to...
Hi,
I am attempting to run the examples of BLE HRS C and BLE HRS Peripherals from the SDK. Getting to the connected state works (discovery and notifications as well) just...
I noticed that the ram setting in this example is from 0x20003440, this means only less than 1KB is for application. But the example in sdk 12.1 the ram is from 20002078....
We want to use IoT SDK where two or more nRF52 chips would talk to each other via 6lowpan, in that case is the ble enabled router necessary for such communication?
I have an nrf51822AC chip connected to another ARM based processor which provides a CAN interface. The two are connected via the UART and we are using the ble_connectivity...
Hi, in the current project I'm working on, I need to develop an Eddystone beacon with UID and TLM frames configured by default. Based on the experimental_eddystone example...
Hi, Nordic
I need write some information to flash, then power off and power on, nRF52 still can read previous information. But now, nRF52 can not read, maybe ESB is still...
Hi,
I'm having issues with my MPU6050 sensor. I'm trying to get yaw, pitch and roll raw sensor values from MPU6050 sensor using DMP on MBED platform but without success...
I have just read nRF52840 Engineering A Errata v1.0, it looks like nRF52840 is like swiss cheese.
When can we expect some solid version of nRF52840 chip on the market?
Hi DevZone
Does the SWF switch at the PCA10040 automatically switch to the antenna I have put on my connection probe? ( www.digikey.com/.../1775923)
Thanks in advance...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
