Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello. I'd like to know. Can I trust to opportunite to firmware my controller (nrf52832) over the air. I mean is there any chance do not be able to do it, for example if last...
I'm using a module that has nRF24L01 mounted.
When I transmit to many PRXs, using the same frequency and channel, I expect to receive
many ACK signal at the same time.
...
I'm using nRF24L01 in a star network and i want to disable ACK.
I write the ACTIVATE command followed by 0x73, then a write to register FEATURE the value 0x01.
In this way...
I am trying to follow the tutorial given on this page:
devzone.nordicsemi.com/.../
However, my eclipse project does not build and created following log
13:55:03 ...
app_pwm_uninit is hanging the code. The control goes to pwm_dealloc() and then in nrf_drv_ppi_channel_free() it hangs.
Using SDK10. I want to change the PWM frequency and...
I am new to eclipse IDE and I am following tutorial on this page:
devzone.nordicsemi.com/.../
I am able to make the blinky project on the terminal and it does create...
Hi,
I have the following piece of code.
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<300;i++)
{
nrf_gpio_pin_clear(PIN_EN_BSTR);
__NOP();
__NOP();...
Hi,
I’m trying to use new SKD 12 secured bootloader but can’t pass signature check in dfu_req_handling.c\dfu_handle_prevalidate() (code after switch case DFU_SIGNATURE_TYPE_ECDSA_P256_SHA256...
Per table 19.4.2 in the nRF52 PS v 1.1:
, what is the difference between CL (load cap) and C0 (shunt cap)? The max ESR is specified for C0 but not CL. The xtal datasheets...
I'm looking for an nRF52 development kit with the PCA10040 1.1.0 or 1.1.1 board and the revision 1 IC . Closest I can find is that SemiconductorStore (Symmetry) claims theirs...
I'm trying to write an iOS app that scans for a specific UUID being advertised
e.g.
NSDictionary* options = [[NSDictionary alloc] initWithObjectsAndKeys:[NSNumber numberWithBool...
The old DFU documentation had nice memory maps explaining how the DFU memory map works.
developer.nordicsemi.com/.../a00056.html
But I can't find this map for newer...
In the ble_nus service (SDK11.0.0 S132 nRF52), what is the simplest way to modify on_write() to send inform the main application the CCCD for notifications has changed:
...
Hi guys,
I can erase all the chip and load the softDevice in command line successfully by nrfjprog.exe. Is there any switch to disable the softdevice protection? Or I need...