Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
We decided to add NFC functionality to our nRF52 open source sensor beacon design, RuuviTag: http://ruuvi.com
I would like to ask your opinion about the antenna...
I'm quite new to the Bluetooth development in gereral...
I want to design a Hardware using the nRF51 Dongle as the reference Design.
The plan is to take the Altium Files...
Hello Nordic Team,
i've get my things working and i figured out how i can set service data and to display it in nRF Master Control.
Now i want to CHANGE my service data...
Hi,
I'm wondering if I'am able to direct advertise when I have established connection (edit: according to this established connection nrf5x is master (central role))? ...
Hello!
everyone:
I use nRF51822 UART Demo(ble_app_uart),test uart interrupt receive data, baudrate is 38400.
if start advertising ,rx loss data ,else rx receive data perfect...
Hi,
I have develop my firmware on on nRF51DK which has n51422 chip.
But my actual hardware has n51822 chip.
So my firmware is working on development board (nRF51DK...
Hi Guys
I've got a strange problem where a binary that works fine on a nRF51822 QFAC does not run on a QFAA
I know that the difference between these two devices is the...
I need to define a few constant arrays for IR implementation. Currently, I define them as
static uint16_t but it takes up a lot of SRAM space. How do I move them to program...
Hi,
I have a setup (in SD310.2.0.0) on nrf51422-qfaae0 in which I'm hoping to receive data on multiple ant channels from multiple networks, but I cant seem to understand...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
Hello,
I am working on a wearable device at the moment. To support iOS and Android at the same time, I have implemented ANCS and nRF UART on the circuit.
When working...
I successfully run "ble_app_hrs_c" on BLE_Central example at 38,400bps on the PCA10001 device.
My modification on PCA10001 board as follows;
cut out 32.768KHz X...
I want to store the max possible data on flash using pstorage , but I noticed that I have to increase the number of Maximum number of flash access commands PSTORAGE_CMD_QUEUE_SIZE...
Hello,
I have got a problem with use SPI. I get hard fault after call spi_master_open(), exactly when sd_nvic_ClearPendingIRQ function is call.
This situation is so specific...
link text from this post , i want to make code, when i press button,device goes into sleep mode.so i use this post's code in ble uart app. my code is here.
/* Copyright...
