Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hi Nordic guys,
we are using uart for communication with another MCU and flow control is used.
Beside the uart communication itself we have out of band signals (on gpio...
Dear Nordic.
I have used to nrf51822 custom device. I confused it because of Uart RX data.
The master device sends blow raw data to client device(nrf51822 custom device...
I'm trying to compile a program on mbed for a BLE Nano, which uses the nRF51822. I've included the nRF51822 library by Team Nordic that's listed on mbed's library wizard and...
Hello
i am trying to upgrade from sdk 9 to sdk 10 .zip version but after installing when i open some examples it asking me to install arm cmsis 4.5. pack and device family...
Hi can anyone guide me in configuring the peripherals of nrf51822 before putting the chip into sleep? For example, timer, i/o pins, etc... which is not needed to reduce the...
Hello, please help me to find nRF52 datasheet, in which are recommended WLCSP footprint, and of course schematic drawing of this module. In your Dev Zone I found only QFN...
Hi,
I'm wondering what speed the NRF52832 radio is clocked at internally. is it the main 64MHz clock or 16MHz like the NRF51?
The reason I'm asking is that I would like...
I'm using nrf51 with 16kb memory
I know that there is a region for softdevice, region for the bootlader and region for the app code and a free region
my questions :...
Hi Nordic support,
I'm pretty new to BLE and I have a system based on the UART example.
On the nRF51-DK, a modified BLE UART Peripheral example using SDK 10.0.0....
Hello,
I am working on S110 v8.0 softdevice and SDK9.0 and need to implement whitelist in our application. I am referring to the ble_app_hids_keyboard example project....
I'm attempting to download and install nRF51 SDK from here:
developer.nordicsemi.com/
Note: The links are ABOVE the masthead of the page (very poor layout!)
I...
Hi everybody,
Here are some related questions based on the same bug :
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I build a test application...
Say, for example, I have a BLE peripheral programmed with S110 on nRF51822. When an Android app connects to it as a BLE GAP central(and becomes GATT client), can any data...
I am trying to get the Device Format Update tutorial to go, but run into a problem while I am programming the using the nrfjprog routine, and the programmer aborts without...
Hi,
My bootloader code was modified to include the device type and device revision when performing the OTA. I used single bank example.
When I made the zip for OTA,...
