Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
hi there!
i'm struggling with the problem about using i2c with IoT SDK.
my project is about transferring sensor data (i2c) through ipv6 over ble , so i used the IoT softdevice...
I'm considering purchasing a nrf51 sniffer USB dongle. I believe I can use this to sniff beacon packets and with wireshark view the packet internals, data, channel number...
Hi
I tried to flash the softdevice with nrfprog, but it does not work. Even with nRFgoStudio it does not work.But with IAR I can program an example of the SDK (without...
Hello, all
I have a problem with ble data exchanging.
I have programmed an application which controls servo motors through phone application.
At the connection, ble...
Hi,
I am trying to use the SAADC to periodically sample an input from AIN0 and send the resultant data over a BLE link to a phone. Going through the forums I saw that the...
Hi,
I am trying to debug the blinky example project on the nRF52 development kit.
I have followed the following tutorial: devzone.nordicsemi.com/.../
Building and flashing...
I'm in the process of designing a circuit that requires Bluetooth. So instead of having a separate chip for Bluetooth and processing, I decided to use a Nordic Semiconductor...
Classic C documentation issue. Are the values that are passed by pointer (p_peer_address and p_whitelist) to sd_ble_gap_adv_start() copied into that function, or do they need...
I'm trying to read the 32-bit value of TIMER1, but it seems the value I read is always 16-bit value. When I debug the value is never above 0xFFFF.
snippet from nrf_drv_config...
The peripheral is actually a dual-mode device, with BLE being a peripheral device.
I can connect to this device and discover the GATT services with the nRF Connect iPhone...
What is the minimum and max value that the NRF_RADIO->TXPOWER register can get set to? The datasheet it takes a signed 8 bit for the setting, but what happens if you set it...
Hello,
I am trying to read data from nRF51422 ADC using SDK51 PCA10028 board downloaded with S130. I tried one of existing ADC with Softdevice examples, it seems to work...
I have meander antenna design on my board with matching network(similar to PCA10031).
Since I don't have access to VNA or Spectrum Analyzer for tuning antenna, I am tuning...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
