I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hi guys,
I can get a rand number use the API:err_code = sd_rand_application_vector_get(buf, bytes_available); but the question is that How can I get a rand number just...
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have a strange problem with pstorage function with nrf51822 with s110 v6.
I need to use nrf_delay ( about 1 second long ) after store and before read.
This is the source...
Hi,
I am using softdevice 6.0.0 and ble_app_hrs example in keil on a custom nRF51822 board. Compilation goes fine but when I try to debug I notice that the firmware seems...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi
I am using S110 v6.0.0
I have written an app that has a single service and I then register the same characteristics until it fails. The properties is 0xA (read/write...
Hi,
The nRFgo Studio v1.16.1 will up side down the contents of old profile XML that created by v1.16.0 or v1.15.x.
And use the new generated services.c and services...
Hi,
So I'm using a BT 4.0 dongle (Laird BT820) to set up a LE notification loop with the nrf8001 (RedBearLab shield on Arduino) using gatttool on Ubuntu 12.04. This works...
I've used the nRF8001 on several projects with good success, so I'm generally familiar with the chip's operation. But I'm seeing an issue on a new (custom) board that I'm...
We are currently researching which BLE chip vendor to use so this question is directed at Nordic personnel familiar with the S110 stack's capabilities.
In a situation where...
I would like to use the nRF51822 evaluation kit as an observer to detect beacons and take action based up the RSSI value. I can't seem to find any source code for S120 or...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
Repro, using the Nordic hid-profile + iOS 7.1.1:
Pair the nrf51822 based hid device via the iOS bluetooth menu.
Turn off nrf-device.
Boot up the nrf-device...
I want use pstorage write and erase flash,as shown below:
//pstorage_init(); // device_manager_init have been called,so there's no need to call
err_code = pstorage_register...
