I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I'm using SDK 4.4.2 and softdevice 5.2.1 to try the HID example. Although it is provided for the nRF6350 kit, I ported (buttons and LEDs) the example to the EV kit...
Hi,
I've been using your nRF51822 with considerable success. I now need to migrate across to an M3 for greater power. I want to keep most of the application code I wrote...
Hi
Thank you for the IOS App "nRF Loader" which was released last week. It works well and offers a lot of possibilities for Nordic developpers. I've one question about...
Hi,
I have just opened my nRF8001 DK. It seems like for the evaluation of the nRF8001, I also need to purchase a nRFgo Motherboard, which is sold separetely.
Where does...
Hello,
I would like to do some code tests and simulations of my application in the keil microvision, so I would like to know if you could give me an example project to...
Is it possible to initiate communicate with an ANT+ device using a nRF24L01+?
I understand that the RF Channel is 2.466 GHz (66), however I do not know what Address(es...
hi nordic guys,
i created one custom profile, which is having two characteristics
my minimum and max conn interval is - 10ms and 50 ms
1. characterisic one will send...
Hi,
i am using accelerometer sensor, which is i2c compatible.
i have nrf51822 pca10001 board.
in accelerometer datasheet it is mention as after every write there...
The documentation clearly state that if the payload length is read as > 32 byte, the RX FIFO must be flushed.
My question is, will that erase all other pending messages even...
How much current can the nrf51822 sink per pin? In the datasheet, I can see that it is at least 5mA. I also see that the chip can drive 3 pins at 5mA, but can it handle more...
Hi
SPI master is 3rd party MCU. SPI slave is nRF51822.
If MCU sends a bunch of data to nRF51822 via SPI, at the same time, BTLE host like celluar phone try to connect...
Hi,
I am using the PCA10001 v1.0 from the development kit and am having trouble measuring the same current as the one from the specification.
I am using the ble_app_proximity...
Hi,
According to nRF51 Series Reference Manual v1.1 , section 10.1.3 there are 3 ways to leave debug interface mode after programming the chip. Assuming that my device...
Hi
i created one timer0 interrupt in ble_app_hrs.
void timer0_init()
{
NRF_TIMER0->TASKS_STOP=0;
NRF_TIMER0->PRESCALER=4;
NRF_TIMER0->BITMODE=3;
NRF_TIMER0->MODE...
