Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
Hi,
I running the radio transmitter and receiver examples provided in the nRF5 v11 SDK.
However, I am observing some unexpected address matching
Setup: nRF5_SDK_11...
Hello,
I use the hrs example of the S130; nRF51_SDK_9.0.0\examples\ble_central\ble_app_hrs_c
I have now 2 belts (A and B) but I do not want to connect to B only to A...
Hi Nordic,
I've read chapters of GPIOTE/PPI in the reference manual of nRF51_Series, and have a basic understanding of these modules. But when I tried to read the SDK code...
Hi,
I am trying make general-purpose s130 app that will be able to connect to central and peripheral at the same time and to exchange informations between them.
At the...
We have bought wt51822-s1 model and now we are facing difficulties in uploading firmware into the device. We are using j link lite cortex m and segger j-FLASH Lite software...
I want to use a timer to track time. Like having a variable that shows minutes/seconds/ms/etc.
But I don't know how to do with that.I want to use the rtc, but rtc1 had been...
Here are the commands I use to upload a program to the device:
JLinkExe -device nrf51422_xxac -if swd -speed 4000
loadbin filename.bin 0x18000
r
exit
It works...
Hi, I'm planning to made a custom PCB using nRF51822-QFAA or QFAC revision 3.
My developing environments are J-Link, IAR EWARM 7.1, SoftDevice 7.1, and SDK 7.2.
I kept...
Dear developers,
Currently, I'm developing a new application that uses Nordic Uart Service (NUS) over BLE.
Everything is working fine. However, I would like reset (delete...
Hi,
I've loaded SD 8.0.0 on the device, but when I try to load application via NRF Studio it always fails.
Im using SDK 10.
Memory settings in Keil:
IROM: 0x18000 0x28000...
I use s110 v8.00, now i need finish the dual bank ble DFU program.
who can offer a example?
the s110 v8.00 is use nrf51422,and used the ram2,
I compile the project,find...
I would like to be able to manually disconnect from a device and then begin advertising.
However, I have discovered that on disconnect, ble_advertising_on_ble_evt handler...
I have an application using N5150 SOC with S210 softdevice and using softdevice_handler, SDK 10.0.0.0, and I'm using Ant-FS to gather data from this device. I only want to...
ble_app_beacon.rar hello there i used ble_app_beacon example. i want to make some modifications. i want to put it in sleep mode after some time and again wake up after some...
Hi,
I am trying to run the example ble_central_and_peripheral_experimental (SDK 9), I program the device with S130 and the hex file. The other two devices I program it with...
