Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Hi,
this is how I initialize and enable LPCOMP
nrf_drv_lpcomp_config_t lpcompconfig = {
{NRF_LPCOMP_REF_SUPPLY_SEVEN_EIGHT, NRF_LPCOMP_DETECT_CROSS},
APP_IRQ_PRIORITY_LOW...
Hi,
I wonder if BLE_ERROR_NO_TX_BUFFERS(s110) and BLE_ERROR_NO_TX_PACKETS(s130) have same meaning.
These marco variables are defined in ble_err.h.
Thank you.
HI,ALL,
i am so sorry for my silly question here.
In ble CORE SPEC,
i saw a sentense (Version 4.2 [Vol 1, Part A])below:
"Device L is shown in the same locality...
Hi,
The SDK6.1 bootloader seems to have problems when used on a Laird BL600 module.
I'm using a BL600 with the SDK6.1 and SD7.1. I want to implement the bootloader in...
Hello!
As per documentation, RSSI is measured during the time, when particular packet is being received. In particular, nRF51822 Product Specification v3.1 states RSSIperiod...
Hi, i have a NRF51-DK (nRF51822 - PCA10028) board and using SDKv10 with SoftDevice S110.
I read everything i could find about this topic and i see people claiming data rate...
I am looking to synchronize collecting of data from outside devices with the connection interval of the nRF51822 and the S110 vers. 8.0 softdevice. Are there specific events...
I want to send big amount of data (10kb) with characteristic of 16 bytes. when the phone side is subscribed to notification I run a loop of data sending.
how can I synchronize...
I have read through the forum on this and I am still not completely clear. Here are my questions:
Can I create characteristics that are larger than 20 bytes? The Bluetooth...
In looking at the nRF51 UART Example I'm wondering about data loss over the Bluetooth interface.
When bytes are sent to the host, is there a re-transmission mechanism somewhere...
Hello,
I was just editing the handling of sent packets and I wanted to evaluate the contents of the ble_gattc_evt_write_rsp_t struct which is part of the BLE_GATTC_EVT_WRITE_RSP...
Hello,
im using NRF 51822 with SDK 10 / S110 8.0. Im working on a project that includes one or two timers (initialized by APP_timer function), the ble calender (like discriebed...
Hi,
Because I didn't want to keep with the last question when this is a tottaly new one, so created another question.
I've tried to get this project to work:
github.com...
We have a communication problem between nRF24LU1+ and nRF24L01+ chipsets. nRF24L01+ uses STM32F4xx MCU on board.
Is there an RF sniffer that sniff the protocol?
