Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
I am working on a wearable GPS tracking device using the nRF9151 DK and testing the GNSS example code. However, I am facing an issue with the cold start time for acquiring...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Suddenly DFU OTA fails most of the time while trying to update units with code & "not secure" bootloader that has been working for years. The FW upload stops at 2% to 8% but...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Hello,
I am using Nordic Thingy91 5G board. My modem firmware version is 1.3.6. My nRF Connect for Desktop version is 5.2.0, which has a Serial Terminal version of 1.5...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
