Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
The GCC linker scripts included with the nRF51822 SDK (checked: 6.0.0 and 6.1.0 as well as nrf51-pure-gcc-setup ) include .init_array sections , but do not specify them as...
Why does the soft device raise a SWI2 interrupt to indicate to the application that an event occurred? In the SDK, callbacks are implemented using function pointers. A function...
Hi!
I'm launching code from example to NUS (ble_app_uart) on nRF52-DK. Everything is going OK, except when I quickly send 4 packets in row from UART to connected Bluetooth...
Hi,
I'm currently working on the project with some hard-timing dependent features. As I've mentioned in another topic, it fails if I have advertising turned on. Turning...
Hi, after I updated my MAC OS X to the latest version EI Capitan, I found my JLink commander cannot connect to the PCA10001 board again even with the Jlink commander updated...
I read somewhere that to get the callback working on pstorage write, read etc, you need to call pstorage_sys_event_handler() in a function set by softdevice_sys_evt_handler_set...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
The nrf51 ARM Cortex-M0 processors, according to the documentation, are "code compatible with Cortex-M3". Does this mean they implement LDREX/STREX instructions for atomic...
Hei,
We would be using nrf52 chip in a very miniature device that should have both BLE and NFC capability. NFC is needed for just as a tag. Thus, nrf52 is a good option....
I moved from SDK 7 to SDK 9. I'm using timers with SDK7
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE, true);
err_code = app_timer_create...
I work with the IAR Workbench and the nRF52 and would like to enable the floating point unit. After installation of the MDK-8.1.0 and the check of the nrf52832_xxaa.i79 file...
