Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi All,
I've happily done all this work before on the Nrf51822 with boot loaders and apps and a happily deployed product.
Thought it was time to shift over to GCC on...
Hi Team,
about power on reset time, not very clear about the description in the SP3.1 as in the attached picture,
why the description are the same?
what's the difference...
Hello,I use s120 and I wnat to send data(write charactheristics value) to all connected peripheral when I receive a character from uart(in uart event handler)?(I use ble_app_multilink_central_s120...
I am connecting to two identical devices, but one is configured as device 'A' and the other is device 'B'. I am currently advertising whether the device is configured as A...
In porting from SDK6 to SDK9, it looks as though
nrf_gpiote_task_config()
has been replaced with
nrf_gpiote_task_configure()
What, if anything, has replaced
nrf_gpiote_unconfig...
I'm using sd_ble_gap_address_set() to randomize mac address and it's working fine. But I'm confused about how to change it back to normal(initial value I see) once I wan't...
i cant find lbs example on \SDK8.0.0\examples\ble_peripheral\nrf51-ble-app-lbs-master\arm and compile.I planned to work with nrf51822 dk. The given example in github shows...
Hello, I have been trying to setup eclipse for the NRF52 off and on all week. I followed the guide on setting up eclipse for the NRF51 and adapted it for the NRF52.
I've...
We have a factory in Hong Kong building and programming nRF51822 modules for us. We may go to a fancier solution in the future, but right now we are using nRFgo Studio and...
If I want to connect the NRF51822 board to Keil using JLink via SWD, I found the SW's clock frequency must below 20kHz. If I choose the higher frequency, the Keil can not...
I know this should be simple, but the prescaler is confusing me...
If I initialize my timers with a prescaler of 0, APP_TIMER_INIT(0, ...)
Then the max timer I can have...
Sorry but I've been stuck on this for a few days now and I have to give up and ask for help.
I'm attempting to set LED0 when BUTTON_0 is pressed and LED1 when BUTTON_1...
Hello all,
I am working on a device (nrf51 and s110) which is going to communicate with multiple centrals (smart phones).
The device uses a whitelist to connect to only...
