Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hi Nordic team,
I’ve been working with the nrf_dm sample from NCS 2.9 to perform distance measurements using multiple nRF52840 devices. The sample works well, and I've made...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
I would like to ask you some questions on nRF51822 Hardware:
From nRF51822 datasheet, a 16M or 32M external clock is needed, now if we have one 26M TCXO is available...
Hi
Maybe you can help me.
I'm trying to get Device Manager to work, but I'm having several problems. Although the Device Manager is being correctly initialized and the...
Hi, I am developing a project under Eclipse Kepler & Mac OS X;
The project
When i debug, and set a breakpoint in the main.c, I got this message:
Then after Steping...
hi, i'm new in nrf module, i use nrf51822, i'm totly confuse what voltage that i should apply on DCC pin? if i want use internal dc/dc than what the voltage and if i use LDO...
after setting BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, I getting BLE_GAP_EVT_SEC_INFO_REQUEST event,
I am using same code as the sample:
case BLE_GAP_EVT_SEC_INFO_REQUEST...
Hi
I am using v6.0.0 softdevice S110 and SDK 5.1.0
In nrf_soc.h the function sd_temp_get() is defined.
The comments there say ..
"p_temp Result of temperature measurement...
Hi,
I use ble_s110_serialization sample code.
I try to notification many 20bytes(total 5KBytes) to my phone, I add some code in ble_app_hrs.
I follow this link to...
I used nRF_Demo_Utility ios app and WFConnector.framework in a sample testing app im building. And when I tried to archive it using xcode it invalidates it with a error message...
Hello,
I’m porting the hids_keyboard demo to work with the nrf51422 dev board. I just changed the #defines for the board in project settings, as well as the pin assignments...
Is there a way to change the scan interval while scanning is on?
I can stop scanning, set a different interval value and start again but that is not my intention, it wastes...
We have some nRF51 beacons kits and we want to connect some external peripherals using the available GPIO pins.
Does any one have an idea on how to solder some pin headers...
I'm trying to implement the ability to change the beacon properties (UUID, Major, Minor) using NRF Beacon Android app. My project is based on s110_nrf51822_7.0.0 (ble_app_beacon...
I'm working with the nRF51822, using the S110 soft device.
My application includes some measurement functions that are timing critical. Ideally, the code would be atomic...
Hi,
Can I use the J-Link Edu programmer to flash the nrf51822? Right now I'm using the J-Link LITE CortexM that I get from the development kit to flash the firmware into...
Hi folks,
I am struggling a little bit with Eclipse.
I just followed this tutorial ( embeddedsoftdev.blogspot.ca/.../eclipse.html) , the project compiles fine, but sometimes...
