Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am developing an application on a STM32 CPU that uses a 51822 through BLE serialization for BLE connectivity.
I have connected some LEDs at the pins of the 51822 to indicate...
Hi,
The nRF51WLCSP needs IR blocking coating and I found here that an example epoxy can be Epo-tek 320. I just want to check if there is any specific time for covering...
Hi
I have been able to successfully write using FDS but I'm unable to read back using the same keys. Here are my code snippets:
#define FILE_ID 0x1111
#define REC_START_ID...
Hello~
I'm using JLinkEXE to flash an nRF51822 chip. When I use nrfgo and press "erase all", it wroks. But after if I flash the s130, I can't erase the s130 with command...
Currently I have a few characteristics which are Authorized Read and Writes. Upon detected of the Authorization from the Central I trigger a few events such as:
Measure...
Hi !
I'm using an nRF52 on PCA10040 board and nRF5_SDK_11.0.0_89a8197. I want to run the peripheral ble_app_template with SEGGER Embedded Studio v2.20. I correctly set...
In an effort to try and determine why FreeRTOS tickles idle is consuming more current than tick mode with an idle task, see this post devzone.nordicsemi.com/.../ , I noticed...
Hi, i am designing a board using nrf51822 and planning to use a MOSFET for reverse battery protection instead of a schottky diode or a normal diode. I am new to this and learning...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I'm developing a nRF52 application that exploits two ADC channels in single ended configuration.
VDD is 3.0V.
For the signal conditioning I've chosen a driving Op...
I've been trying to get my head around using a BLE central and making connections so I've loaded up the multi-central example to figure out just how everything works. I turned...
Hi everybody!
I am working with ANCS (nrf51822 SDK 9.0) I am confusing on setting the connection parameters which are MIN an MAX connection interval.
Firstly, I set...
Hello,
I have some characteristics on my device that are containing some configuration data.
Every single variable is a global variable.
The values can also be changed...
