Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear Nordic Team,
I am using Nordic DK board,
Now i want integrate UART to hid-mouse application. So that whatever data i can receive , will send to HID device without...
Hello everybody,
I'm trying to use pstorage module but it seems that the example_cb_handler function is never called when I try to store data.
I noticed similar issues...
There have been a number of other older topics with this same error message symptom, but I've tried all the solutions proposed and none have worked to solve this specific...
Hi.
I am using SD s110, ble_app_uart example from SDK10.0.0 on dk pca10028 as a peripheral. The central is a laptop running linux.
I am trying to establish a connection...
As noted here , a lower interval will give quicker connection - but at the expense of power consumption.
With a 4s interval, it seems that it is likely to take several...
Let's say I add two PPIs which both trigger off of the same event. One of these PPIs is connected to the CHG[0].EN task, and the other is connected to the CHG[0].DIS task...
In the GTT_2_Introduction nRF52 document there is a picture with text
-42 dB Selectivity (2'nd CI). As far as i concerned it's about Carrier-to-interference ratio. But what...
Hi.
I am using DK PCA10028 V1.1.0 for my devlopment. The SD is ver 8.0.0, the SDK is the latest and keil v5. The IC is nRF51422QFAC. I am trying to flash the examples from...
Hello, Is it possible to configure nRF's USART to work with Smartcards (ISO 7816)?
The ISO7816 specification defines the bit rate with the following formula:
B=(Di/Fi...
I use the " nrf51-ble-dfu-symmetric-signing " example from GitHub.
The application download over dfu works fine on the PCA10028 board.
But how can I install this bootloader...
dm_distributed_keys_get returns address of local variable 'peer_enc_key';
sdk version: nRF51_SDK_9.0.0_2e23562
in function ret_code_t dm_distributed_keys_get(dm_handle_t...
hello guys,
I'm working in a project & I added some sort of security to the project, I enabled the bonding & MTIM flags through:
#define SEC_PARAM_TIMEOUT 50 /**< Timeout...
Hello,
The 32kHz external oscillator is it required by S110 softdevice v8.0.0?
I haven't see this information in soft device specificaion v2.0.
Thank you.
Hi everyone,
I am using the Arch BLE running firmware version 221 (most current one).
Whenever I create more than 3 PwmOut objects (from the mbed library), the MCU just...
