Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am having an odd problem.
nRF52
softdevice S132 V2.0.0
I have a bootloader and application. when I program them directly to the device they both work fine and can...
I need to get three ADC data from acceleration sensor with nrf51822. I tested getting a ADC data using simple_adc_pca10028(Keil_v5/ARM/Pack/NordicSemiconductor/nRF_Examples...
Hello
We are about to move an old design based on the NRF51 to the more powerfull NRF52.
In this context we would like to use some of the new API’s that has been introduced...
Recompile dfu_dual_bank_ble_s132_pca10040 example from SDK v11 with softdevice v3.0 header. DFU is advertised, but not able to connect to it. always timeout,
There are three...
I made a product with nrf51822AC(based on SDK6.1&softdevice7.3), now we want to do BQB testing and I am working on our board's DTM code.
I have tried example "\Nordic\nrf51822...
Hi Nodic:
I use the PCA10028 V1.2.0 board , and use "nRF51_SDK_9.0.0_2e23562" SDK, ..nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_uart\pca10028\s110\arm5_no_packs...
Hi,
In SDK11 I was able to update advertised device name without restart, just handled write on the characteristic and update advertising data (through a second call to...
I'm going through pin_change_int example and can't understand how we tell controller where locate the function for our event.
Probably it occures in channel_port_alloc that...
I'm trying to communicate with an EEPROM chip using SPI. When I run under the debugger, the EEPROM doesn't respond; without the debugger running, it seems to work fine.
...
Hi everyone
I am working with nrf51822 sd 110 v.7.1
If I change from XXAA to XXAC, do I have to change the IRAM settings? If yes, which are the correct settings?
...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
I think similar to but not exactly this question: devzone.nordicsemi.com/.../
Can I get a quick clarification here....
I'd like to encrypt the zip data / application...
Hi everyone,
Somebody knows if its possible and how to configure a Pin code to establish the connection between the nRF51 peripheral and a phone as a central?
Something...
Hello,
The nRF51824 was announced over 3 months ago, is there a datasheet/product spec available anywhere?
My main curiosity is whether the power efficiency has changed...
