Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Not a question, reporting a typo. InfoCenter "nRF52832.Product Specification.RADIO.Packet configuration" about the sixth paragraph "The S0INCL field in PCNF0 determines if...
Hello,
When I use the .hex of the tutorial, works ok. But when I compile the tutorial works Ok until when it suppost to sleep (after the timeout time), then gives an error...
I'm working on my owm dfu service and until recently I used pstorage_raw for handling memory. Now as I wanted to implement bonding, I added the peer manager, because I'm not...
What are the expected wait states when reading data from RAM and FLASH on the nRF52? This is stuff on the DCODE bus.
What I'm seeing whilst profiling is a load instruction...
Hello,
I had this compiler error issue .
I know this dirty laundry shall be cleaned by Keil and Microsoft Windows. But you still can help if you add to your SDK project...
I have clone nRF51 mesh project(nRF51-ble-bcast-mesh-master.zip), and I can find BLE_gateway sample project in the zip file, but I can't find a led_mesh project. Does anybody...
In SDK 11, there was an immensely useful function known as NRF_LOG_PRINTF. in SDK 12, this seems to have been replaced by NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR. However...
pin 2 is for turning on and off at sepecified time...
pin 3 is for turning on the light whrn button is pressed and turned off automatically as time decided in the program...
I have been debugging this problem for a few days and have exhausted all of my options. I am relatively new to embedded development so user error is not out of the question...
Hi,
I need to load ble code to mrf51422. I read on the forum that I can do it using nrf51 dk but did not get the steps. Couod someone give me detailed description about...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello to everyone!
I'm digging documentation of SDK. and I meet a lot of doxygen things like this
/**@brief Macro for configuring a pin to use a GPIO IN or PORT EVENT...
Hello Everyone,
I want to program the BMD-300 with the nRF52 Preview Development Kit.
I have connected:
BMD-300 -> nRF52-DK
SWDIO -> SH_SWDIO (pin #4) on P20
...
Sorry for probably stupid question..
All the time in SDK we set need bits through the mask, for example
NRF_GPIOTE->CONFIG[idx] |= (pin << GPIOTE_CONFIG_PSEL_Pos) &...
Hello,
I am looking to get started with NRF52. I am very familiar with TI BLE so not a beginner.
I am looking for a high level introduction to the nordic soft devices...
