Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Compiling nordic project I get errors:
compiling main.c...
..\..\..\main.c(37): error: #5: cannot open source input file "softdevice_handler.h": No such file or directory...
I am not sure if this is a limitation with Keil or Nordic SDK. I made another copy of ble_app_uart inside SDK_11 s130 and renamed it with a much longer name. I tested that...
I'm using the nRF SDK5 v11.0.0.
I'm trying to test out UART Logging in the simple blinky example bundled in the SDK.
I added NRF_LOG_INIT() and then a NRF_LOG("Testing\n...
Hello everyone,
I am trying to implement a bootloader to my application to be able to enter in DFU mode.
I am using nrf51822 (32KB ram 256 flash) and s130.
I have taken...
My understanding is that the nRF51 is known to need a fairly stiff external pull-down resistor on SWCLK to avoid noise putting the chip into debug mode. I note that the nRF52...
I'd like to know how to implement a bootloader for the Nordic SoC nRF51822-QFAA-R in order to boot the softdevice and some firwmare. If will be great getting an application...
Does nRF52832 have battery monitor?
I can't find in the datasheet if there is an externarl circuit to monitor the battery. I'm using a CR2032 coin cell battery.
Tha...
Hi,
I'm developing some firmware that will hopefully run on a few different kinds of nRF52 device.
Is there a way of detecting if the DC-DC converter's inductor/capacitor...
Following situation:
My device acts as central (connecting to ble sensors) and as peripheral (transmitting and receiving data from mobile). Several services (Heart Rate...
Hello,
I followed this tutorial:
devzone.nordicsemi.com/.../
and added the RTT files to the project, however, after I compile i get this message :
and when...
Hi guys,
I am using the RFduino nrf51822 chip. I am using the TIMER2 interrupt and it works fine. But when I try to use the BLE along with the timer interrupt both don...
Hi,
I have have one ble project which is using softdevice s110. so that i want to extend this project by adding DFU service to it like shown here
devzone.nordicsemi.com...
hi,
i have PCA10028 dk board. i want to flash code in this board using dfu. i have generated Zip file(both soft device and application(example ble_app_hrs example)) using...
I am using this DFU library github.com/.../IOS-DFU-Library . On iOS 10 while processing DFU I receive error RemoteInvalidState in didErrorOccur method with description "Device...
I want to know the maximum range for major and minor in Ibeacon frame, as it is of 2 byte can we set any values from 0 to 65535 or is there any limitation.
