I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi
Recently in the release notes of the SDK12 I noticed a line about updated the MDK update:
Included a critical MDK update (v8.7.1)
My SES project uses the...
Hi,
Is there an example available for Nrf51822 BLE HID (nrf5 SDK v11) with Feature and Output reports?
I've added an output HID report to HID mouse example from SDK and...
Hello.
I use nRF52 and tried to make the shared channel.
There are 1 Master and 1 ~ 3 Slave device.
When the master device send the notification messages to slave...
Hi,
I just did a quick diff using these two commands
> find nRF5_SDK_12.0.0_12f24da/ -type f | grep --text -v -e "c$" -e "h$" -e "s$" | sed 's/.*\///' | sort -u > exclude_list...
Hi
we are switching from NRF51 to NRF52.
Putting the same (very basic) inits for sd and advertising, leads to NRF_ERROR_INVALID_PARAM..
This is my source:
#define...
Hi,
I downloaded the latest SDK V12, coped the example HEX from the BLE Beacon and it worked fine.
I tried to then compile using Keil, it compiled, but I noticed that in...
Hello,
I am currently using the TWIS (slave!) peripheral to get data from a I2C master. Now I would like the ability to place the nRF52 in deep sleep mode with sd_power_system_off...
i am using UART service for implementing BLE App on iPhone-4s by using objective-c.
i downloaded old source code of UART but it can't work.
so can i get latest updated UART...
Hello Everyone,
I am working on nRF51 can any one tell me how can i get current time in microsecond?
micros() return current microsecond time in arduino. I wants same...
I am new at this, I need to enable the OTA DFU mode on a nRF51822 QFAC chip on a pcb (the pcb has bluetooth).
how can I program it? what do I need to configure?
I am trying...
Hello,
I can't copy file from mail after updated nRF Toolbox to v4.0.4. (iPhone5s & iPhone 6Plus)
The app crashed when I select Copy to nRF Toolbox.
Any solutions?...
I found we have to build micro-ecc.lib on our own, so I follow the below link to start to build it:
Installing micro-ecc
Then, we meet the below to errors:
Makefile...
