Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I'm trying to program the bootloader together with an application+SD132 3.0 on the nrf52, but my device gets stuck with the bootloader when I finish programming it...
Hello, I used s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
Is there any example to study the central bond?
I use the examples->ble_central->ble_app_uart_c, the following...
Hi All,
I have hardware setup which has four or more beacons in peripheral mode at particular radius ( approx 10 m) and have a beacon in central mode.
The central beacon...
I'm using the Nordic as a BLE solution, and it is just passing along data through the UART to another chip through the UART. However, I'm not sure how to just pass the data...
Greetings,
I am using pynrfjprog (9.0.0) to write a HEX file to an nRF52 device on the nRF52 DK. I am wondering if there is an easy way to verify the write using API.py...
We're looking to implement buttonless DFUs with the NRF52 and are a bit confused how to send 0x01 to the control point of the service. Is this a control point that is already...
I have tried to export a very simple mbed program (blinks LED1 and LED2 and writes to Serial (USBTX, USBRX)) with no success. I am running on an Ubuntu 32 bit distro. This...
Hi,
Is there an example for the Sleep modes and 2Wire on the nrf24LE1 with the SDK? Just found some 2Wire examples with a modified HAL which doesn't seem to work for me...
I'm trying to get the I2C on the nrf24LE1 working. I'm using the modified Library from nAN-20. It doesn't do anything. Can't see anything on the oscilloscope. It's an nrf24LE1...
Hi,
I'm using nRF5_SDK_12.0.0_12f24da and s132_nrf52_3.0.0_softdevice to do the mutilink and it's almost ready. We want to do the OTA on it. I think the mutilink is working...
Hi there,
It isn't obvious from the reference layouts on the downloads page for nRF51822-CFAC if the ground plane is supposed to create a 50 Ohm trace going into the balun...
Hello everyone, i have a task where i need to transfer 50-100kB of data from ble peripheral to a central device. I have read many posts here and i have a pretty good idea...
Hi, I work with the nrf51-ble-driver_win_0.5.0. I changed the heart-rate-collector to discover the characteristic of connected devices. Maybe I'm blind. But the ble_evt_handler...
I want to accomplish something very simple: use a timer to output a continuous square wave on a certain pin, at 30-60kHz or more. It doesn't have to be PWM or anything fancy...
Hi,
I'm working on a BLE application which use ECC.c (Elliptic Curve Crytography). The problem is Keil has found an Error:
._build\nrf52832_xxaa.axf: Error: L6218E:...
