Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
in the ble multilink central example i'm not understanding where the functions in client_handling.c are exercised some don't seem to be used in main or client_handling (client_handling_dm_event_handler...
I am reporting a problem that might bite you. A Waveshare NRF51822 module comes with a "Passed" sticker on the back (solder side) that makes the module stand off the mother...
Hi,
We are trying to have a thin beacon design. But we are having difficulty in finding low profile inductor for dc-dc converter matching the recommended value of 10uH...
I'd like to use Logic Analyzer in uVision 5.2 and ulink2 for analyzing variables in nrf52832.
In my understanding, I need to use SWO and configure Trace setting properly...
Hi,
I need to capture a demodulated, manchester encoded signal (16 bits long). The data rate is about 50kHz (give or take). Currently, I am configuring a PPI with timer1...
Hello,
I'm using nRF52840 which is surpport Bluetooth 5. I couldn't understand why it can do 8 X range and 2 X data rate than Bluetooth 4.2.
Besides, how to use Bluetooth...
I observe strange behavior while reading value for long characteristics.
I have characteristic 100 bytes long (read only).
In GATT client I must read value with subsequent...
can i get nrf 51 beacon antenna printed on beacon kit. its semicircular in shape... can any one help me
i want eagle library of the antenna
please help
Hi,
I want to reduce the current both in the TX mode
and in the system on idle mode as much as possible.
I measured the current consumption of nRF52DK with the original...
With s132 v3, in addition to configuring the GATT to receive larger packets like so:
ble_enable_params.gatt_enable_params.att_mtu = 247;
err_code = softdevice_enable...
Hi all,
I'm working on secure bootloader on sdk12.2.0, And Installed nrfutil v2.3.0 by following the user guide nrfutil v1.2 successfully and it working well without any...
Hi everyone,
I'm using SDK 12.2 on nRF51822. Trying to get the buttonless dfu app example to work.
Here's what I do:
Compile buttonless dfu app.
Generate settings...
Hi,
I'm new to python and also the NRF51 dongle. I need to build a python script to connect my NRF51 dongle to a BLE device without using Master Control Panel. I tried using...