Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi I'm looking to Program the NRF9E5 RX board so that the LED remains high until the switch is pressed on TX. So the TX button would turn the LED high and remain so until...
Hi,
How can I use nrf905 with an Openwrt based module? Are there any driver for operation systems? These modules have many gpios.
Openwrt based modules are simply Wifi modules...
Have anybody a solution for my problem ? nRF24LE1 is first in low power state (PWRDWN is 3 or 4) and wakes to send a message. Mostly the message has the same PID identity...
Hi,
I am using the SPI ports (0 or 1) to communicate with a peripheral chip, and the operation is undeterministic.
For test, I put the SPI code to read the peripheral...
I have bought from ebay 10 nRF24L01 and I'm trying work on a ,for more that 7 days, project sending 7bytes data. I have build (on a breadboard) the circuit described on that...
Hello everyone!
I have two sets of PIC18F45K22 and nRF24L01, one as a Tx, and another one as a Rx. I have programmed the PIC using mikroC compiler. My question is how do...
I am wnating to clarify, if i can use the Gazell protocols on the nrf51422? I can't find it in the SDK for the 51422, but it is in the sdk for the 51822.
There are some include dependencies that go like this:
app_uart.h -> app_util.h -> app_error.h -> nrf_error.h
and nrf_error.h is under Include/s110.
In order to debug...
Hi,
The err_code shows NRF_ERROR_INVALID_STATE when called sd_ble_gap_adv_start(). I want to know why it happen, and how to handle it. This happened upon the ble disconnected...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
Is it possible with Nordic NRF51422 to perform accurate proximity ranging to make sure that a circle of 2 to 3m but not more is identified in a reliable way?
What is the...
I'm assessing whether ANT is suitable for the network deployment I have in mind, and I would appreciate to hear any thoughts you have on this.
I have a network of say 20...
Hi,
I want to change the GAP params such as connInterval, slaveLatency, and have some questions:
1.can I call sd_ble_gap_conn_param_update directly or need to send...
I used nRFgo Studio(version 1.15.1) to program S110 and application through my Jlink. But it's not worked in version 1.16.0.
It's not a good feature! :(
