hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
image description (http://)when i try to flash the led binky programme to nRF51822 Ek. i am getting device error and LED also glowing continuously.
1.this device error was...
So I was thinking of having the following:
nRF24L01+
to balun (e.g., Johanson 2450BM14A0002 or Anaren BD2425NnRF)
to PA/LNA RFX2401C
to PCB antenna
If...
Hi all,
I want to clarify are there any deference between "connection_id" and "conn_handle" ?
I use a multilink central application with 8 possible peripherals devices...
Hello,
I have some difficulties to make an ant acknoledgement with my nrf51422 (s210), and i would be grateful if you could help me with it. (SDK used 12.2)
I have 2...
Please give me info about configuring a timer at given timeout. For eg,. if we want to blink LED for 30 seconds, how to configure them using timer events.
What is the optimum reset strategy for Debugging the nRF52832 with a Segger J-Link Plus?
(Setting of Project_Options/Category:J-Link_J-Trace/Reset)
nRF shall not...
Hi,
I am using SD 120 Ver 2.1.0 and SDK 8. I am getting disconnection with reason 0x3E sometimes. After disconnection even master is scanning, It wont get connected with...
I've been working on a separate problem with the NFC Type 4 library when I ran across this. I can duplicate it in the experimental_writeable_ndef_msg example.
All I did...
Hi Nordic Forum!
I've been trying to run a test program (pin toggle) on a custom nRF52832 board.
First, I tried the same program on the HDK to toggle pin P0.17 (LED1...
When I use additional VS UUID, should I use sd_ble_uuid_vs_add(), se_ble_gatts_service_add() in order?
example,
sd_ble_uuid_vs_add(); <- VS1 UUID
se_ble_gatts_service_add...
Hello, I am developing with pc-ble-driver using python. I noticed that the Bluetooth connection becomes disconnected when I alt tab out of the gui I made. Is there a solution...
Hello,
I am using SEGGER Embedded Studio together with a nRF52832 and I am trying to read an EEprom register containing a 32-bit floating point value in four bytes (register...
