Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hello,
I would like advertise for an unlimited time.
Why value 0 in ble_gap_adv_params_t::timeout don't work ? Device don't advertise anything. It works fine with a positive...
In the nrf_drv_gpiote in SDK 11.0, I can only find a function to get the address of the out task for a gpiote channel. Shouldn't there be a similar function to get the addresses...
I am working on nRF51822 ble_app_bps and I want to use Estimote SDK to monitor beacon on the background.
I also changed UUID, Major, Minor value: UUID.fromString("00001810...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
Hello Nordic Support Team,
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. Since there are more than 7000 devices...
I'm trying to get the default SDK v12.0.0 BLE App UART running with SoftDevice S130 v2.0.1, with minimal customization (I just enable the Peer Manager module in sdk_config...
Hello,
I am using i2s through the driver : "nrf_drv_i2s". After playing a song, I have a residual current consumption about 1mA unless I call nrf_drv_i2s_uninit every times...
Hi everyone!
I flashed an application with the help of DFU bootloader. The application runs for the first time . The application contains a service that lets the application...
Has anyone had the problem recently of trying to make or debug from within GCC and hitting an exception immediately? I believe I picked up an update to Eclipse because after...
Hi, I'm using SDK12 and I'm trying to implement button debouncing. I have initialized one of the nRF52 board buttons using app_buttons.c. In the infocenter I read that debouncing...
Hello,
I am using ble_app_template project. I want to add uart in this project. So I am referring uart project from peripherals. Now in ble_app_template project under nrf_drivers...
Hi,
recently I experienced a strange behavior on the nRF51 chip, that is at a certain point some gpio lines remained held high, even if the firmware set them to low (both...
I clone the repository on GitHub, which is the accompanying code for the Application Note nAN-36 "Creating Bluetooth Low Energy Applications Using nRF51822", in the nrf51822...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards. I want to check my runtime. So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
