I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I'm working with the SAADC peripheral example and I'm trying to add some code to set the ADC resolution. I've tried doing this several different ways based on what I can find...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and connected the...
Hi,
I would like to have a confirmation of my interpretation of the consumption information that I found in the NRF51822 product spec to estimate the power consumption...
Hello,
reading the revision history in the S130V2 document, it seems only documentation has been changed.
Are there any specific functionality / bugfixes / api changes...
i want to use 2-wire to do the communication of two nrf24le1. one is the master, another is slave.
I don't know how to set up the master and slave.
Is it the code shown...
Hello All!
I am going to use nRF52832 as a network co-processor. I will be using UART as the interface between the main processor and nRF52832.
My question is how to go...
Hi,
i update my characteristic every 1 second with a new value. the notification is set for the characteristic and it will notify my phone about the new value.
at the...
I have a PCA100028 not working anymore. not sure what I have done to the board.
I have a couple of other PCA100028's work well on the same computer.
The program left on...
hi
its first in this event
on_ant_evt_channel_closed
and then
storage_access_complete_handler();
then it try to advertise by this
sd_ble_gap_adv_start...
I use s130 /center ble_hrs example , add 7 peripheral characters and add dfu,but when I want to update codes, I find it start dfu,start bootloader and connecting.... all the...
hi.
in s110 there is no problem but when use example ble_ant_app_hrm in s310 nrf51422 the ble getting error.
its error code is 536881912 :( .
in debug point error ocure...
hi.
i wrote a program in s110 and it work fine . in it i creat my own service .
but when i want use my service in s310 softdevice in this line i get error forbiden or error_code...
How can I flash SD110 and Serialization on Wavetek's WT51822 shield? I am working with an ST nucleo64 and mean to use STlink for flashing.
I found an application note from...
what is the procedure to find connected device is bonded or not, should i store the device, application or service context in persistent memory to help recognizing bonded...
